Beware of recent phishing e-mails. Use our official contact addresses only.
413-284-9975
Adaptas

Ionization Gauge Tubes, Bayard-Alpert Type

Catalog F26-F27
Home
Ion Gauge Tubes, Bayard-Alpert Type
Hover over image to zoom

Description

Series G Ionization Gauge Tubes are hot cathode gauges of the Bayard-Albert Type intended for pressure (density) measurement from 10-3 Torr down to 3 x 10-10 Torr. These tubes have been designed to provide long trouble-free operation and are carefully cleaned, assembled and packaged so that they will not contaminate your clean system. Both the burn-out-resistant iridium type and the dual tungsten types are interchangeable.

G Series

Burn-Out Resistant Iridium Filament (G Series)

The burn-out-resistant filament is made of iridium with a layer of thoria cataphoretically coated on it. This provides long filament life and stable, easily controlled electron emission at relatively low filament operating temperatures. Because iridium does not oxidize rapidly, even at high temperature, occasional accidental exposure to atmospheric pressure while hot will not appreciably damage or shorten the active life of the filament. The burn-out resistant model is designed for convenient and reliable connection to standard connectors.

T Series

Dual Tungsten Filament (T Series)

The dual tungsten filament model is also designed for use with the same gauge cables. By connecting control unit filament leads to contacts "C" or "D" of the connector, either filament may be used by merely reversing the connector 180 degrees on the tube base. Because the two filaments are independently connected, one may be used to operate the gauge and the other operated as a desorption filament.

The bifilar design supports the grid at its midpoint so that the unsupported length of grid wire is only half that in conventionally wound grids. Thus the tendency to sag during outgassing is greatly reduced.

Bayard-Alpert Ion Gauge can measure vacuum from 10-10 to 10-3 torr.

Features

  • Bayard-Alpert Design
  • Dual Tungsten or Burn-out Resistant Iridium
  • Non-sag Bifilar Grid
  • Linear Response
  • 3/4" or 1" Pyrex or Kovar Tubulation
  • Response from 10-10 to 10-3 torr

Specs

Physical Data
Filament Voltage 3 to 5 Volts AC
Filament Current 4 to 6 Amps AC
Grid Voltage +150 Volts
Grid Outgas 6.3 to 7.5 Volts@ approx. 10 Amps.
Collector Voltage -20 to -50 Volts
Sensitivity Tungsten Filament: 100μa/μ @8 ma grid current (Nitrogen)
Iridium Coated Filament: 100μa/μ @10 ma grid current(Nitrogen)
Linearity 10-4 to 10-10 Torr @ 10 Ma
10-3 to 10-4 Torr @ 1 Ma grid current
Electrical Data
Bulb Material Nonex 7720 Glass
Tube Diameter 2 1/4" max. O.D.
Tube Length 6 3/4" Maximum
Tabulation See Chart
Mounting Position For best results, it is recommended that tube be mounted vertically
Recommended Either Winchester Electronics
Socket Connector P/N A7SH or Continental Connector P/N 7-16SH

Connectors

Connector Plug Data

The G Series is designed for convenient and reliable connection to a standard connector. The burn-out-resistant version is mechanically and electrically interchangeable with similar models using Continental Connector Corp. type 7-16S connector. (Refer to above diagram).

Gauge Tube Pin Data

The two tungsten filament version is designed for use with the same connector. Connect control unit grid leads to contacts "A" and "H" and filament leads to contacts "C" and "D" of the connector. Filaments can then be switched by merely reversing the connector 180 degrees. This eliminates the possibility of damage to tube by applying grid outgassing currents to filament (s). (Refer to above diagram).

Cross Reference

Cross Reference Table

Ion Gauge Tube
Part No. Description Quantity
In Stock		 Price
EA		 Order
G75P 3/4 in Pyrex Iridium 0*Standard lead-time for non-stock items is approximately two weeks depending on the item. $219.00
Qty
G75K 3/4 in Kovar Iridium (Finnigan #00105-01500), Bayard Alpert 0*Standard lead-time for non-stock items is approximately two weeks depending on the item. $224.00
Qty
T85P 3/4 in Pyrex Tungsten 0*Standard lead-time for non-stock items is approximately two weeks depending on the item. $115.00
Qty
T85K 3/4 in Kovar Tungsten DISCONTINUED------
G100P 1 in Pyrex Iridium DISCONTINUED------
G100K 1 in Kovar Iridium DISCONTINUED------
T110P 1 in Pyrex Tungsten DISCONTINUED------
T110K 1 in Kovar Tungsten DISCONTINUED------
G75KHS 3/4 in Kovar Iridium/Thoria, Hi Sensitivity, 1.6 (Finnigan #00105-01510) 0*Standard lead-time for non-stock items is approximately two weeks depending on the item. $210.00
Qty
G100KF25 NW25 Flange Iridium for HP5989 DISCONTINUED------
* Standard lead-time for non-stock items is approximately two weeks depending on the item.
† Call for availability.
shopping cart Ordering information. International (non-US) prices available through your local dealer.
Related Products
Popular Items also Purchased
  • Agilent/HP MS 5970 MSD® and 599X Series FilamentAgilent/HP MS 5970 MSD® and 599X Series Filament
    New filaments for your Agilent 5970 MSD.
  • PTFE Ferrules for Ion Gauge TubesPTFE Ferrules for Ion Gauge Tubes
    They are available in two compositions, PTFE and Glass filled PTFE.
  • Agilent (Hewlett Packard) Mass Spec Ion Gauge TubesAgilent (Hewlett Packard) Mass Spec Ion Gauge Tubes
    Our standard G75K Bayard-Alpert ion gauge tube will fit all models of HP mass specs except the HP5989 MS Engine.
  • PTFE, Glass Filled PTFE Ferrule for Ion Gauge TubesPTFE, Glass Filled PTFE Ferrule for Ion Gauge Tubes
    These 3/4" PTFE Ferrules are used to install Ion Gauge Tubes.
  • Inland 45 Mechanical Pump OilInland 45 Mechanical Pump Oil
    Inland 45 is the highest quality rough pump oil you can use for your mass spectrometer.
  • Santovac 5P Ultra and polyphenyl ether vacuum pump fluidSantovac 5P Ultra and polyphenyl ether vacuum pump fluid
    Santovac 5P Ultra has the same properties of Santovac 5 but guarantees minimal amounts of the 3 and 4 ring polyphenyl ethers; less than .02% and .1% respectively and for ultra-clean applications such as mass spectrometry.
  • Agilent 5989 FilamentsAgilent 5989 Filaments
    Filaments for your Agilent 5989 mass spectrometer.
  • FC-43 (Perfluorotributylamine) Calibration CompoundFC-43 (Perfluorotributylamine) Calibration Compound
    This compound is available in bottles of 35, 100, and 200 grams.
  • Granville-Phillips Vacuum Gauge ControllerGranville-Phillips Vacuum Gauge Controller
    Granville-Phillips 340 Vacuum Gauge Controller (VGC) measures pressure from less than 1 x 10-9 Torr to atmosphere, utilizing an ionization gauge and two Convectron gauges.
  • Convectron Series 275 Vacuum GaugeConvectron Series 275 Vacuum Gauge
    The Granville Philips Convectron Gauge tube used on the 5971 and 5972 mass spectrometers is available from S.I.S. This is a direct replacement for the HP original and screws into the fitting shown above.
  • Electron Multipliers, DeTech 2300 Multipliers for Agilent 5975/5973/597X/1100Electron Multipliers, DeTech 2300 Multipliers for Agilent 5975/5973/597X/1100
    Get a DeTech 2300 Electron Multiplier here. Used in Agilent 5975 MSD (without TAD)/5973/5972/5971/5970/1100 LC-MSD mass spectrometers and backed by a 100% no-nonsense warranty. Developed by Detector Technology, Inc.
  • Copper Gaskets for Vacuum FlangesCopper Gaskets for Vacuum Flanges
    The below listed vacuum flange copper gaskets are made from OFHC copper.
  • VG Copper GasketsVG Copper Gaskets
    Copper used.
  • Copper Gaskets for HP Mass SpecsCopper Gaskets for HP Mass Specs
    All gaskets are .080" thick.
  • Copper and Gold Plated Cu Gaskets for Thermo/Finnigan MSCopper and Gold Plated Cu Gaskets for Thermo/Finnigan MS
    The following copper and gold plated copper gaskets are available for the vacuum flanges on Thermo/Finnigan mass spectrometers.