Home
- ▶
- Heaters/Source
- ▶
- Agilent Heaters and SensorsMass Spectrometry, Scientific Supplies & ManufacturingScientific Instrument Services 5973 Source Heater Tamper Resistant Allen Wrench 5973/5975 Quad Sensor 5985 Source Heater Assembly Agilent Interface Heater Assembly 5971 Interface Heater
- ▶
- MS - Agilent/HP (This Page)
SIS supplies a wide range of parts, supplies, and repair services for your Agilent/HP mass spectrometers. If an item or instrument is not listed, contact us and we will try to add it our product line.
Agilent/HP part number cross reference
If you know the Agilent/HP part number, search for it here:
5977 The Agilent 5977/A MSD is a quadrupole MS, circa 2013, interfacing to the Agilent 7890B GC.- 5975 The Agilent 5975 MSD is a quadrupole MS, circa 2005-2010, interfacing to the Agilent 6890/7890 GC.
- 5973 The Agilent/Hewlett Packard HP 5973 is a quadrupole MS, circa 1996, interfacing to an HP 6890 GC.
- 5972 The HP 5972 MSD is a quadrupole MS, circa 1992, interfacing to the HP 5890/6890.
- 5971 The HP 5971 MSD is a quadrupole MS, circa 1988, interfacing to the HP 5890.
- 5970 MSD The HP 5970 MSD is a quadrupole MS, circa 1982-6, interfacing to the HP 5890 GC.
- GCD The HP GCD (G1800A) is a quadrupole GC/MS, released circa mid-1990's.
- 5992/5993/5995 The HP 5992/5993/5995 is a quadrupole MS, circa ~1976-1979's.
- 5985/5986/5987/5988 The HP 5985/5986/5987/5988 is a quadrupole MS, circa ~1980's.
- 5989 The HP 5989 (MS Engine) is a quadrupole MS, circa early ~1990's. It interfaces to the HP 5890 GC.
7000 The Agilent 7000 a triple quad GC/MS, circa 2008-2013.
4500 The HP 4500 is an ICP-MS, circa 1994.- 6100 The Agilent 6100 is a single quadrupole LC-MS, first released circa 2006, including the 6110, 6120 (lower end), 6130, and 6140 (higher end). Later versions include the 6150 (circa 2010) and 6100B (circa 2010). It is followed by the InfinityLab LC/MSD and LC/MSD XT.
- 6200 The Agilent 6200 is a TOF LC-MS. first released circa 2008. Variants include 6210, 6220, 6224, 6230, and 6230B.
- 6300 The Agilent 6300 is an ion-trap LC-MS. first released circa 2006. Variants include the 6310, 6320, 6330, and 6340 (circa 2006).
- 6400 The Agilent 6400 is a tripple quadrupole LC-MS, first released circa 2006. Variants include the 6410 (circa 2006), 6420, 6430, 6460, 6470 (circa 2015), 6490 (circa 2010), 6495 (circa 2014).
- 6500 The Agilent 6500 is a quadrupole TOF LC-MS. first released circa 2006.
- 7500 The HP 7500 is an ICP-MS, circa 2000-7.
Parts for Agilent
Filaments Replacement filaments for your Agilent/HP mass spectrometer
Multipliers Scientific Instrument Services, Inc. provides replacement detectors for your Agilent mass spectrometer. Multipliers are from the major manufacturers of electron multipliers.- Source Heaters & Sensors Replacement source heaters and temperature sensors
Vacuum & Accessories Agilent Supplies and Services for your Vacuum needs.
Transfer Line Supplies Agilent Supplies and Services for your Transfer Line needs.
Probes Probes for Agilent MS for use in your lab.
Baseplate O-Ring for 5973/5975/5977 Large brown viton o-ring.
Ceramic Insulators The following ceramic insulators are made from high purity alumina ceramic.
ESI/Jet Separator Tools Each tool has a 4" long stainless steel handle with a tungsten wire cleaning tip.
Autosampler Agilent Supplies and Services for your Autosampler needs.
GC Supplies The new Graphitized Vespel® Injection Port Liner Seals are designed to replace the Viton® 'O' Ring Seals.
Other Supplies More Agilent Supplies and Services
Mass Spectral Libraries
(NIST 23 and Wiley Libraries)Identify unknowns from EI (GC/MS) and MS/MS spectra. The most trusted, largest, and widely used libraries.
Repairs for Agilent
- All Repairs SIS has an extensive shop facilities to perform the repair services for Agilent.
- Filament Repair
Source Cleaning Expert cleaning & repair of mass spectrometer sources.- Cross Ref. Scientific Instrument Services carries a wide selection of parts for all models of Agilent (Hewlett Packard) mass spectrometers. In order to aid you in the selection of replacement parts for your instrument, the following part number cross reference chart can be used. If a part number is not listed, it either means we do not have that part in our inventory or perhaps we are not aware of the Agilent part number in relation to our inventory. If you are looking for a part not listed below, give us...
Other Parts for Agilent
- Air Cleaners, Data System
Autosampler Vials Vials are manufactured from Type 1 borosilicate glass tubing to hold uniform wall thickness.- Brass Nut Available in packages of 5 nuts.
- Ceramic Insulators The following ceramic insulators are made from high purity alumina ceramic.
Clamp Insulator, 5989 The Vespel® clamp insulator used in the 5989 mass spectrometer source.
Copper Gaskets All gaskets are .080" thick.- Engine, Additional Parts Additional parts for the HP5989 MS Engine are available.
Hose Adaptor Fittings The standard fitting is for 3/4" hose.- Injection Port Liner Seal The new Graphitized Vespel® Injection Port Liner Seals are designed to replace the Viton® 'O' Ring Seals.
Inline Connector S.I.S. supplies stainless steel connectors manufactured from type 316 stainless steel.
Interface Heater/Sensor Assembly Used in the jet separator interface and other areas.- Jet Separators, 5970 SIS supplies new parts or repairs old parts on your Thermo/Finnigan instrument.
Lead Protector Are available in both quartz and ceramic.
Lens Insulator The Vespel® lens insulator used in the 5989.- Jet Separator Cleaning Kit Each tool has a 4" long stainless steel handle with a tungsten wire cleaning tip.
Open Split Interface SGE has developed an inexpensive system for interfacing glass or vitreous silica capillary columns to mass spectrometers (MS).
Probe - DEP The DCI probe utilizes a replaceable filament wire at the end of the probe which serves to both hold the sample and heat the sample.- Probe - Direct A ½ inch probe inlet, provides the user with greater flexibility and much faster ramp rates than the standard HP DIP probe.
Probe Inlet System Has been designed to prevent the occasional venting of the mass spectrometer by accidentally pulling the probe past the vacuum seals.- Probe - High Temperature The probes can be used from ambient temperature up to 800 degrees C with ballistic temperature ramp of over 700 degrees C/min.
Probe Port Parts SS4P4T Pump Out Valve and HP12 Probe Inlet Seal
Probe Tip Replating - Gold The gold plated probe tips used with the Hewlett Packard direct probes can be cleaned and replaced with gold if they become dirty.
Pump, Rough Pump
(Edwards)This miniature two stage pump features an alternative inlet connection position at the side of the pump so that overall installation height can be reduced to a minimum when required.- Pump, Rough Pump
(SIS replacement)Low cost rotary vane vacuum pumps designed for S.I.S. for the scientific community. Comparable to Edwards RV3 & Adixen 205 Series. Attachable to Agilent 597X MSD's. 
Source Heater Assembly, 5985 Replacement source heater for the 5985.
Spacer, Metal These stainless steel spacers correspond to HP# 05985-20106.
Syringes, Autosampler A comprehensive range of syringes for GC autosamplers is available.
Transfer Line Tip This new design eliminates any Inlet metal contact with the sample, the capillary column protrudes slightly through the end of the tip directly into the source.
Vacuum Measurement System The vacuum measurement system to monitor the source pressure is optional for the 5971.- Vespel® Repeller Insulator Vespel® Repeller Insulator for Agilent.
Injection Port Liner The injection port liners for the Agilent 5890 GC.